Get the Best IPTV Service
WilloBuild - WilloBuild OpenViX 6.6 Series | Page 63 | Techkings
What's new
By:
Filters

WilloBuild WilloBuild OpenViX 6.6 Series

Gentlemen said:
Hi guys I hope I don’t interfere with your threads but I need some advice. I have Zgemma H7C with openvix 5.4 willobuild. I have FTA channels from sat dish 28 (of course no cables) and IPTV channels. Naturally I am zapping from channel to channel but it seems to me that my box crashing or freezing after a while if I watch channel from Sat and IPTV alternatively.
Thank you in advance and regards
G.
Click to expand...
Hi guys I don't want to hijack the thread with my issues however I thought flashing up to 6.5 would sort the freezing issue but unfortunately it has not.. can't figure it out what it is cousing the issue..Any ideas and advise would be much appreciated..here is a log that I think it is from this morning..
 

Attachments

  • Enigma2_debug_2024-05-27_20-03-14.zip
    516.4 KB · Views: 2
Last edited:
Gentlemen said:
I have FTA channels from sat dish 28 (of course no cables) and IPTV channels. Naturally I am zapping from channel to channel but it seems to me that my box crashing or freezing after a while if I watch channel from Sat and IPTV alternatively.
Click to expand...

What does 'FTA sat, no cables' mean?
What are you using to create IPTV bouquets?
 
It's not something I can test. I don't have the XE plugin or a sub for it.
I would flash ATV on another partition if you have multiboot, and see if it works on that.
 
As a start, try disabling hdmi cec and see if that improves things.

Ensure your tuner configuration is correct for all tuners. Just because it works, it does not mean it is correct. To be correct, it must match the hardware attached to the tuner. The debug log log is a continuation, so I can't tell properly. But it seems you have configured one of the tuners as a motorised dish.
 
Last edited:
Abu Baniaz said:
As a start, try disabling hdmi cec and see if that improves things.

Ensure your tuner configuration is correct for all tuners. Just because it works, it does not mean it is correct. To be correct, it must match the hardware atatched top teh tuner. The debug log log is a continuation, so I can't tell properly. But it seems you have configured one of the tuners as a motorised dish.
Click to expand...
Ok thanks mate I will check them all and give it a try..
 
You can describe the reception hardware (dishes/aerail) attached to each tuner without touching the box. Please also attach the first part of debug log. Inspect the file called settings in /etc /enigma2 for usernames/passwords. Remove any and then zip and upload here.
 
Abu Baniaz said:
You can describe the reception hardware (dishes/aerail) attached to each tuner without touching the box. Please also attach the first part of debug log. Inspect the file called settings in /etc /enigma2 for usernames/passwords. Remove any and then zip and upload here.
Click to expand...
I have disabled the hdmi cec, Tuner A config to 28 , Tuner B and C are disabled..?? Files attached..
 

Attachments

  • IMG_6970.jpeg
    IMG_6970.jpeg
    687.5 KB · Views: 11
  • Enigma2_debug_2024-05-28_22-03-35.zip
    37.4 KB · Views: 6
You have posted a picture of the tuner configuration overview. Thanks.
You have decided not to describe the equipment connected to each tuner. Nobody can compel you to provide information.

Your log shows a storage device mounted as /media/hdd/. (Good)
EPG obtained by Engma2 is being saved onto the storage device. (Good)
Your debug log shows the hdmi cec command coming through. Please try a reboot later.
This debug log does not have the expected service reference xxxx, (Good)

Where is XE plugin downloading EPG?
 
Last edited:
The log was produced before I've changed the hdmi settings, I don't know where is the EPG downloading for XE I've checked the settings and it's enabled.
 

Attachments

  • Enigma2_debug_2024-05-29_05-04-05.zip
    17.6 KB · Views: 2
You must log in or register to reply here.
Back
Top
Flash Sale Popup