VU+Duo / Wooshbuild

[bazcfc1]

You install via a command either via terminal by entering your box ip address into web browser then down the left hand side under extras terminal should be there then enter opkg install http://wbuildx.co.uk/setup.ipk or use putty enter your box ip adrees in press connect then type root press enter will say logged in as and enter the opkg install http://wbuildx.co.uk/setup.ipk press enter

 

[makido]

http://vuduo

 

[atiq1]

http://vuduo

makido! sorry what was that

 

[makido]

To open webif is that not what you wanted like?

 

[pabloescaban]

If you have atv 6.3 you just add infinity now by using webif/Terminal
Paste command line in and away you go

 

[atiq1]

If you have atv 6.3 you just add infinity now by using webif/Terminal
Paste command line in and away you go

Thx again Guys! I can only find MAC address for this box in order to use above route for Wooshbuild infinity now that I have loaded OenATV 6.3 successfully. Where do I find IP address for his box pl.? One more push Pals. O

 

[bazcfc1]

Menu information then network

 

[pabloescaban]

Thx again Guys! I can only find MAC address for this box in order to use above route for Wooshbuild infinity now that I have loaded OenATV 6.3 successfully. Where do I find IP address for his box pl.? One more push Pals. O

Menu/information /network

 

[makido]

Or open command and prompt on your laptop and type ping vuduo
This will give you the ip address of your box

 

[atiq1]

Sorry about all the stops and starts Guys. Got the IP address, managed to get as far as Open Webif page but down on the left in Extras, there is no "Terminal" option. Although following options are there. Box is connected to the internet. Where else can I find the "Terminal" option . Any help pl

• Box Info
• Settings
• AutoTimer
• BouquetEdito

 

[dsayers2014]

Menu, plugins green to download plugins then extensions terminal.

Alternatively install putty on windows How to use Putty for Unix/Linux commands

 

[atiq1]

Thank you so much to everone who contributed to this thread. Did manage to install Wooshbuild in the end.. Fantastic amount of help.

 

[atiq1]

Thank you so much to everone who contributed to this thread. Did manage to install Wooshbuild in the end.. Fantastic amount of help.

Must share my experience Guys! Using Putty route, I tried to install Wooshbuild infinity, using the right command. It installed that alright but when I ran it, I could see Wooshbuild Infinity screen and while going through the Menu options, it encountered software problem and it closed down and restatrted facing the same problem at the same stage like last time.
So taking it into account the opinion of respected wise guys here, I decided to use Grogbuild and it went fine but when the box stated again, it didnt have any logo in the background like Wooshbuild . It is giving me Open ATV logo and Menu. As it is not official Wooshbuild Infinity method, How can I check if Grogbuild method has been sucessful and installed? Thx

 

[pabloescaban]

Did you paste the grogbuild command line in webif/Terminal?
It asks you if you use cable and asks for your netid etc and a few other questions then flashes atv and puts grogbuild on

 

[atiq1]

Yes I did everything as required. But like wooshbuild infinty logo should there be a grogbuild logo in the background?

 

[pabloescaban]

Yes I did everything as required. But like wooshbuild infinty logo should there be a grogbuild logo in the background?

Not really, there's a monkey onscreen when it's rebooting

 

[atiq1]

Not really, there's a monkey onscreen when it's rebooting

so that means it has has not loaded grogbuild . i shall give it another go

 

[pabloescaban]

How are you doing it?
You initialise the usb in the box.
Then paste grogbuild freerange command line in terminal and answer 5 or 6 questions and it does everything itself

 

[atiq1]

How are you doing it?
You initialise the usb in the box.
Then paste grogbuild freerange command line in terminal and answer 5 or 6 questions and it does everything itself

Pablo! I repeated the process once again thoroughly, the box rebooted without any problem with the same results but then reading Grog's loading instructions for GBFR, these lines caught my eye:-

"As we do not use an image in Grogbuild FreeRange it will install in just minutes on any Engima2 set top box that has openATV installed."
so would it be fair to assume that there won't be any monkey logo in the background for GBFR. please correct me if i am wrong.

 

[pabloescaban]

There's no monkey logo when in use.
There's one on screen when it's rebooting