WooshBuild Install openatv 6.4

[Moss Miah]

Yes sat connection is nice and tight. Even if VM /Sly channels 1-5 came through I would be happy. One thing I have just notice is when the box reboots and the numbers are counting up I realised the boxes seems to stop at 49 and doesn't count up any further but 30 secs later the box goes in wooshbuild and all seems fine.

I think the box is crashing and not doing the full reboot. I am confident this is what the issue is with the box?

If this is the issue my next question would be how do I resolve this so it does a full reboot until the numbers reach 00. ?

 

[moshibeth]

Yes sat connection is nice and tight. Even if VM /Sly channels 1-5 came through I would be happy. One thing I have just notice is when the box reboots and the numbers are counting up I realised the boxes seems to stop at 49 and doesn't count up any further but 30 secs later the box goes in wooshbuild and all seems fine.

I think the box is crashing and not doing the full reboot. I am confident this is what the issue is with the box?

If this is the issue my next question would be how do I resolve this so it does a full reboot until the numbers reach 00. ?

I bet your satellite cable is in the loop connection instead of the LNB at the back of the box which will stop you getting a signal

 

[Moss Miah]

I have double checked sat connection it's definitely not in the loop connection. The VM turner is showing good signal strength but all FTA channels 1-5 are still coming through as blank ?

I still don't understand why the box when rebooting only counts up to 49 and no further. Its almost seems its crashing when it hits this point of the reboot...?

 

[dsayers2014]

FTA channels 1-5 are still coming through as blank ?

Are they SD not HD channels?

I still don't understand why the box when rebooting only counts up to 49 and no further. Its almost seems its crashing when it hits this point of the reboot...?

Possibly a skin issue, try the default skin to see if you get the same

 

[Moss Miah]

The SD channels are blank on vm and sly. Can you tell me how I change the skin back to the default setting..?

 

[dsayers2014]

Menu, setup, usage and gui, skin setup

 

[Moss Miah]

I've set the skin to default. The box went to reboot just before it did that a message came up stating the network interface needed to restart then box just froze on me.

So I switched it off from the back and on again, the box rebooted again but while rebooting the box become stuck on the WB screen. However the skin did indeed change to the default setting.

Since changing the skin setting to default the box is now in a loop where it just keeps rebooting itself even if you put the box back on standby Its rebooted it self. Its so far rebooted itself 15 times thereafter I just ended up switching it off at the back of the box.

Can you please advice me what to do to resolve this new issue...?

 

[Moss Miah]

Hi Moshbeth, when you say willobuild do you mean wooshB...? If so I have reflash it with this bit of software a couple of times and no joy... the box I have is the H5.2TC

 

[moshibeth]

Hi Moshbeth, when you say willobuild do you mean wooshB...? If so I have reflash it with this bit of software a couple of times and no joy...

No i mean willobuild.Why would i put willo if i meant woosh just click on resources at the top of the page and as i said make sure you have a usb mounted or you will continue to have issues

 

[Moss Miah]

Apologies my misunderstanding. Can you please advise me where or how I go about getting this software? I'm a newbie and still learning and trying to understand these boxes and the way they work so please go easy on me.

The chap I normally to get my box reflashed etc has has gone Awol and I can't find any help near to where I live therefore has resorted for help on this forum.

 

[moshibeth]

Apologies my is misunderstanding. Can you please advise me where or how I go about getting this software? I'm a newbie and still learning and trying to understand these boxes and the way they work so please go easy on me.

The chap I normally to get my box reflashed etc has has gone Awol and I can't find any help near to where I live therefore has resorted for help on this forum.

I have said already miah if your read the post correctly. Top of every page has a tag called resources click on there

 

[dsayers2014]

WilloBuild ViX 5.4 for Zgemma

 

[Moss Miah]

Is there any other way to resolve this rebooting issue other than reflashing the box with willo build...?

 

[moshibeth]

Is there any other way to resolve this rebooting issue other than reflashing the box with willo build...?

Do you have a usb or hard drive mounted in the box

 

[Moss Miah]

Yes I have a 250mb USB stick connected to the back of the box via usb, but nothing else mounted in the box or at the front USB.

 

[Willo3092]

WilloBuild ViX 5.4 for Zgemma

That's for H3 and H5 Zgemmas. H9's use the standard setup because they are supported by ViX. WilloBuild - WilloBuild OpenViX 5.4 Series

 

[dsayers2014]

That's for H3 and H5 Zgemmas. H9's use the standard setup because they are supported by ViX. WilloBuild - WilloBuild OpenViX 5.4 Series

He has a H5.2TC it's not the original poster that is having issues he's hijacked someone else's thread causing confusion lol

 

[moshibeth]

He has a H5.2TC it's not the original poster that is having issues he's hijacked someone else's thread causing confusion lol

Put willo in his place cheeky monkey

 

[Willo3092]

He has a H5.2TC it's not the original poster that is having issues he's hijacked someone else's thread causing confusion lol

It was Moshi who threw me lol

Reflash it with willobuild and you will have no more looping. .You must keep a usb or hard drive mounted in the h9.2s boxes as they are real problematic

 

[moshibeth]

It was Moshi who threw me lol

Total denial and if you check the small print your responsible for your own actions. Tell that to judge rinder