How To : Install Multi LNBs on one dish

[linesman66]

This is the switches i used

Technomate TM-4S - 4-way DiSEqC Switch

 

[linesman66]

Buy the insulated cable covers that
Slide over your f connectors at the Disqce switch
Provide a good waterproof seal

 

[linesman66]

With my Disqec switches
Port1 13.0E 13F/13G
Port2 19.2E 1KR/1L/1M/1N
Port3 23.5 E
Port4 28.2 E 2E/2F/2G

Then the other satellites dish
I have two wf.100 satellite cables
Tunner A is set Disqec A/B
13.0E Hotbird 13F/13G 19.2EAstra 1KR/1L/1M/1N
Tunner B single Sat 28.2 East Astra 2E/2F/2G
I wired this way so if the Disqec switch ever
Fails i still have 28.2 E

 

[linesman66]

Ncam 15 now available

enigma2-plugin-softcams-ncam_V15.0-r0_all.ipk » satup.net

 

[linesman66]

This is the changes

Ncam V15.0



- omnicrypt: Add ecm support.

- Update reader-videoguard-common. this change has been in the forrums for a few years but not yet implemented thanks to (Didov3).

- revert to discarded parts, as they are also an important part of the module-serial.

- fix openssl dependency.

- added Fransat V6 cards to hanlde ECM of UHD Channels thanks to Constance and rumas84.

- add Dreambox Reader detection

- Dgcrypt 0x4AB0 with EMM * adding EMM Support for DGCRYPT 0x4AB0 thanks to lnj * adding support for non-standard ISO 7816-3 protocol for pcsc module thanks to lnj

- add hide Provid-SA IRDID

- Fix 'can't find 0xf0 in emm...' on Fransat V7 card (Thanks to nitida and OptimumPower)

 

[davyc007]

Afternoon guys. I have a v8 uhd and viark sat 4k. Both have 16e/19.2e/28.2e atm. I have added 23.5 but it’s only a single lnb. I have a splitter lying around. Can I use a splitter to create x2 outputs then connect these into a diseqc for each receiver? As long as I only watch 23.5e on 1 receiver at a time? If it’s possible would I drop much quality? Cheers.

 

[gilvey]

Afternoon guys. I have a v8 uhd and viark sat 4k. Both have 16e/19.2e/28.2e atm. I have added 23.5 but it’s only a single lnb. I have a splitter lying around. Can I use a splitter to create x2 outputs then connect these into a diseqc for each receiver? As long as I only watch 23.5e on 1 receiver at a time? If it’s possible would I drop much quality? Cheers.

Stick a multi lnb on instead save messing about

 

[Ferret.]

Afternoon guys. I have a v8 uhd and viark sat 4k. Both have 16e/19.2e/28.2e atm. I have added 23.5 but it’s only a single lnb. I have a splitter lying around. Can I use a splitter to create x2 outputs then connect these into a diseqc for each receiver? As long as I only watch 23.5e on 1 receiver at a time? If it’s possible would I drop much quality? Cheers.

It would work but youll most likely forget at some point and burn out the splitter. Rough guess you loose 5% signal strength